Custom-fit household hardware

Measure it. Size it. Have it made.

Choose a common replacement part, enter the dimensions from the original object or mounting location, and inspect the result before requesting a manufacturing quote.

Measured preview

Washer

100%

Ready to review

Diagram scales to the values entered.—

Measure every direction and use the largest reading.

Parts that look round or square can vary slightly from side to side. Measure all applicable sides, record the largest value, and enter the full actual size. Printed colors are only a preview.

Helpful digital-caliper measurement notes

Clean first. Remove dirt, burrs, adhesive, and loose material from both the part and caliper jaws.
Zero before measuring. Gently close the jaws, press zero, and confirm the display reads 0.00 mm.
Use millimeters. Keep the caliper in mm mode and enter the displayed value without converting from inches.
Outside dimensions: use the large lower jaws for widths, diameters, thicknesses, and outside edges.
Inside dimensions: use the smaller upper jaws for holes, slots, and the inside of caps or tubes.
Depths: extend the depth rod from the end of the caliper and keep the caliper body flat against the opening.
Use light pressure. Close the jaws until they just touch. Do not squeeze flexible pieces or force the jaws into an opening.
Keep it square. Hold the jaws flat and perpendicular to the surfaces; a tilted caliper usually gives a larger false reading.
Check multiple positions. Rotate round parts and measure opposite sides, ends, and several points along the part.
Repeat the reading. Measure each important dimension at least twice and use the largest repeatable value.

Finish your request

Material and quote details

Choose filament

Select the material that best matches where and how the part will be used.

PLA Indoor general useBest for rigid indoor parts away from heat and weather.Pros: crisp detail, rigid, economical, and a clean finish.Cons: softens sooner in heat, has limited outdoor durability, and can be brittle under impact. PETG Outdoor capableBetter for outdoor, damp, warmer, or impact-prone applications.Pros: tougher than PLA, better moisture resistance, and handles moderate heat better.Cons: less crisp detail, may flex or creep under constant load, and is not intended for extreme heat. ABS Tough + higher heatBest for durable functional parts used indoors or in warmer operating areas.Pros: tough, impact resistant, easier to sand or machine, and handles heat better than PLA.Cons: lower UV and weather resistance than ASA, can shrink or warp while printing, and may be more brittle than PETG in some impacts. TPU 95A FlexibleBest for flexible caps, feet, grips, bumpers, and vibration control.Pros: flexible, impact resistant, grippy, and difficult to crack.Cons: not rigid, dimensions can be less precise, and it is unsuitable for parts that must hold a stiff shape. ASA Weather + higher heatBest for long-term outdoor exposure and warmer operating areas.Pros: strong UV and weather resistance and better heat performance than PLA or PETG.Cons: can be more brittle under impact, may cost more, and some shapes are more difficult to print without warping.

Quote details

Tell me where to send the quote. Contact details are used only to review and respond to this request.

Your name

Email address

Phone number optional

Shipping ZIP or postal code

Quantity

Operating environment

What will this part be used for?

Additional notes

I understand that an entered hole, opening, shaft, or mating diameter is treated as the minimum nominal design size. Up to 0.6 mm total clearance may be added to help mating parts fit, but the design will not intentionally make the opening smaller than the size I entered.

Fit-sizing rule: up to 0.6 mm total clearance

Every entered hole, opening, shaft, or mating diameter is treated as the minimum nominal design size. The design will not intentionally reduce it below the customer’s entered value. When a part must slide over, onto, or around another object, up to 0.6 mm total clearance—approximately 0.3 mm per side—may be added to help prevent a tight fit.

A measured outside diameter used to create a matching opening receives the selected clearance in that opening. Finished exterior dimensions that do not mate with another part remain at the entered nominal size. Actual printed dimensions can still vary slightly by material, printer calibration, and finishing, so the final allowance is confirmed during quote review.

Finished sizing this object?Review everything that will be included with the custom quote request.